Listen Live
The Light 103.9 Featured Video
CLOSE

How many of you have a green thumb? That’s a special skill some might say. Those that are deemed unlucky usually will have to sit back and while watch while everyone else’s plants become ready for harvest. Well for those who have an interest at any level of producing a winning garden this is right up your alley.

Behold the watering can, a practical gardening tool crying out for some whimsy. Using shards of china and porcelain figurines, mosaic artist Bonnie Arkin transforms old galvanized metal watering cans into adorable decorative pieces that have been sitting in her garden for years. Granted, the mosaic weighs the can down quite a bit so it’s impractical to use the completed can for actual watering, unfortunately. The same technique can be applied to flowerpots, planters, steppingstones, vases, birdhouses – and even bowling balls to create garden orbs.

TOOLS NEEDED:

(You’ll find these items at craft and hardware stores.)

Goggles

Tile nipper

Plastic bags

Putty knife

Premixed grout and adhesive

Sponge

Gentle scrubbing cleaner, such as Soft Scrub

Craft knife

DIRECTIONS:

1. Treasure hunt. Collect beautiful or endearing items you want to piece together into a mosaic. Traditionally, these are tiles or shards of china that can be found at flea markets and thrift stores or donated from family members. But widen your scope: buttons, charms, beads, coins, pebbles, sea shells, jewelry and even Lego pieces. Arkin advises against using cardboard, paper or fabric because they’re too fragile.

2. Break the china. Wearing work goggles, place a plate upside down inside a plastic bag; smack it once in the center with the tile nipper. (Arkin said one student who couldn’t bring herself to bash her china double-bagged it and ran over it with her car. For the sake of your tires and anyone in the vicinity, we are not recommending this.) This type of mosaic is called pique assiette.

3. Cut the shards. Keep your goggles on. To cut large shards into smaller pieces, hold a shard in the mouth of the tile nipper, less than one-quarter inch, and squeeze the handles for a clean break. That’s called “nipping.” You typically want your pieces to be the size of postage stamps, but go larger or smaller to stay proportional to the frame you’re working with. To shape the shards into circles, use your tile nipper to nibble at the edges. That’s called “chipping.”

4. Apply the grout and adhesive. Traditionally, mosaic artists affix their pieces to the surface with adhesive before spreading grout on top – a good strategy if you’re working on intricate designs; Arkin prefers to save time by purchasing premixed grout-and-adhesive-in-one (such as Simplefix) and slathering it on in one step. Rest the can on its side on a towel. Using a putty knife, spread a quarter-inch layer of the grout-adhesive mixture over the can surface.

5. Design. Lay your items out like puzzle pieces and let your creativity guide you. You may have to cut pieces smaller as you go around the curve of the can so that they will rest flat. It’s important to “butter” the back of every piece with the grout-adhesive mix before pressing it onto the can so that it sticks better. If the grout starts to stiffen, dip your fingers in water and wet it. If you make a mistake, pull the pieces off, put them in water and start again. Wipe the grout off the front of the shards with a wet sponge as you go along to keep the grout from drying on top.

6. Wait. Let the can dry for a week. Because it’s round, you have to work in sections, letting the first section completely dry before turning it over to do the next area, and so on.

7. Tuckpointing. Use a gentle scrubbing medium, such as Soft Scrub, and a scouring sponge to scrub and buff the surface; scrape off any dried grout with a razor blade or X-acto knife. The grout will shrink and crack as it dries, so you will need to spread another layer of grout on top of the finished piece to fill in the grooves. Smooth it over with a wet sponge immediately – you don’t want the grout to dry on top.

8. Wait again. Let the can dry another three days, and you’re done! If you wish, add more decorations, like porcelain flowers or a string of pearls, with glue; Arkin recommends Household Goop.

For Full Story: